The Curt # C59496 wiring harness is a universal-fit item that will work on any vehicle with a 12V wiring system, so it'll work great on your Land Rover LR2.
You will need to use the included circuit tester to locate the brake light circuit behind the vehicle tail light. Once this circuit is located it will be connected to the smaller red wire coming from the converter box.
Next, locate the left turn signal circuit and connect the yellow wire to that circuit. The green wire is then ran... view full answer...
To install a 7-way on your 2008 Land Rover LR2 you would need to start with a 4-way. That will provide the turn signal functions and then you can use a 7-way adapter to convert it to the style of connector you need.
For the 4-way you would want to start with the part # C59236 which is a universal wiring harness that's been tested as a fit for your vehicle.
Now if your trailer does not have brakes all you would need is the part # 37185 as an adapter to convert the 4-way to a 7-way.
If... view full answer...
Yes, the Upgraded Modulite Vehicle Wiring Harness Kit w/ 4-Pole Trailer Connector and Installation Kit
Item # C59496 does include the dust cover to help protect your 4-Way wiring harness.
If you do not have a mounting bracket already, you can use the Tow Ready Mounting Bracket # 18144 so that the 4-Way is not just hanging off of your vehicle. For a no-drill installation you can use either the Long Bracket # C57202 or the Short Bracket # 18140.
Another option to keep your wiring harness... view full answer...
Once installed the Curt trailer hitch # C13052 will have the receiver recessed under your 2011 Land Rover LR2. We have yet to install one on a Land Rover so I do not know the exact figure but based on the diagrams of similar hitches installed it appears that it would be too far for the old Hitching Post bike racks to clear the rear bumper.
What you can do is follow the instructions in the picture I have included to determine where the center of the hitch pin hole will be once the hitch... view full answer...
I could see needing to trim the rear fascia for the Land Rover OEM hitch, but the Draw-Tite hitch does not require fascia trimming.
It is designed to fit just below the rear bumper. I imagine the hitch that Land Rover offers is designed to fit and look like the optional factory hitch.
Below I have added a link to the instructions for the Draw-Tite hitch, 75688, so you can read through the instructions. There is also a diagram that shows where the hitch will be positioned in relation to... view full answer...
I spoke with my contact at Canine Covers and while the exact dimensions of the Canine Covers # DCL6343CH aren't available he was able to tell me that the # DCL6343CH is custom design for the 2008-13 Land Rover LR2 - it will work with the - (2nd row up or down and w/ extension to 1st row seat back) (So, it will cover the back of the front seats- that front seatback section is w/o padding since it is just for protection- not sitting/laying on).
The top of the cover is Polycotton and it... view full answer...
The Curt Trailer Hitch Receiver, part # C13052 is a verified as a good fit for your 2008 Land Rover.
This is a Class lll hitch and it has a 2 inch receiver opening.
The Euro ball mounts we offer are not designed for a 2 inch receiver. They fit 1-1/4 inch receiver openings.
You might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball,... view full answer...
From there you would need to convert the 4-way to a 7-way so that you can install the brake controller. For that you will want the Brake Controller Install Kit and 7-Way Adapter part # ETBC7. I attached installation instructions and an install video for this product as well. These aren't specific to your vehicle but they will show you the same process that will be applied to your 2015 Land Rover LR2.
For a brake controller I would recommend the Prodigy P2 Brake Controller part # 90885.... view full answer...
While we do not have any grille guards that will work with your 2007 Land Rover LR2, we do have a wide variety of roof racks that'll work great.
If your vehicle has a slick roof, I recommend going with the Thule WingBar Evo Crossbars # TH711400, with the Evo Clamp Feet for Thule Crossbars # TH710501, and the Fit Kit for Thule Evo Clamp and Edge Clamp Roof Rack Feet # TH145123.
These crossbars have integrated t-slots to accompany any roof mounted accessory, has a nice weight capacity at... view full answer...
For your 2012 Land Rover LR2 the Draw Tite hitch part # 75688 would be my recommendation as it fits your vehicle, does not require drilling and because it comes with a bracket for trailer wiring already welded to it.
For trailer wiring you'd then want the part # C59236 which is confirmed as a fit. Then for a bracket to bolt to the hitch wiring bracket you'd want the part # 18144.
If you wanted to do some towing you might be interested in etrailer ball mount kit # 989900. It comes with... view full answer...
The difference between the two Rhino-Rack roof rack systems you referenced, # RR67GR and the rack consisting of parts # RRVA126B-2, # RRRLKVA and # DK010, is in the length of the Vortex Aero crossbars and the type of leg kit.
The ROC25 Roof Rack # RR67GR has legs into which the Vortex bars terminate while the other system has longer through-type cross bars that extend further out beyond the leg assemblies. Please refer to the linked photo and video. Some customers prefer the more finished... view full answer...
When we do an install video, we will typically get the measurement you are looking for. Unfortunately, we have not yet had the opportunity to install a hitch on a 2011 Land Rover LR2.
With high hopes I called Curt hoping that they would be able to provide that dimension, but they do not measure that dimension during their test fits.
This being said, Curt was able to provide me with some dimensions that we can use to approximate the distance. All is not lost if you are willing to crawl... view full answer...
The distance from the hitch pin hole to the sleeve is 2 inches for the Trailer Hitch Extender for 1-1/4" Trailer Hitch Receivers - 7" Long # e68YR. view full answer...
I do have an option for you, but there is not an adapter for a 4-way connector to fix the issue you are having with the LED light strip on your 2008 Land Rover LR2.
Instead you will need to install a Load Resistor in each of the 3 circuits in the light strip using the # DI34ZR. This will correct the flashing issue you are having.
I included a video of the # DI34ZR for you to take a look at. view full answer...
The Draw-Tite trailer hitch, part # 75688 will work great on your LR2. This is a Class lll trailer hitch and it has a 2 inch receiver opening.
For hitch-mounted bike carriers I recommend a platform-style carrier. These are easier to load and unload and they provide a sturdy way to hole the bikes in place. One of the bike racks I recommend is the Swagman XTC4 4-Bike Rack, part # S64665. This has adjustable wheel hoops that will accommodate 4 bikes with a wheelbase range from 27-1/2 to... view full answer...
I checked with Thule and the OutWay 3 bike rack, # TH56BV, will fit your 2008 Land Rover LR2.
If you will be carrying women's, children's, or alternative frame bike racks, I recommend using the bike adapter bar, # TH982XT, for greater ground clearance and to carry the bikes more level. I have included a link to a video that shows how the adapter works. view full answer...
For a great fit for your 2012 Land Rover LR2, I recommend the Draw-Tite Class III Max Frame Round Tube Receiver Hitch, Item # 75688. It does not require drilling and bolts onto your frame. For trailer wiring, I recommend the Kit, Item # C59496, which is confirmed as a fit. If you need a bracket for the hitch wiring, I recommend Item # 18144.
If you need a hitch ball mount and hitch balls for towing a trailer, I recommend the Etrailer ball mount kit, Item # 989900. It includes 2 ball... view full answer...
Since you already have a 4-Way trailer connector on your 2008 Land Rover LR2, you will need installation kit # ETBC7 and a brake controller. You may not have to do any splicing. On the ETBC7, the 4-Way you have plugs into the mating 4-Way on the ETBC7 adapter.
The white wire grounds to the vehicle frame. The purple wire is for reverse lights and would be the only rear wire that would potentially have to be spliced into the vehicle wiring. But if the trailer does not have reverse lights... view full answer...
The 26" Greystone Electric Fireplace with Remote Control # 324-000065 does force the air out utilizing a blower fan. It works like a space heater with the different temperature settings, a timer, and automatic setting as well. I've attached a picture of the blower fan for reference. The blower fan doesn't have different settings like low, med, high on any of the units. It is temperature regulated.
I've linked the page to all your options and they will all have the blower fan similar... view full answer...
To haul bikes as well as your skis and snowboard on your 2008 Land Rover LR2 HSE, there is one great option, starting with a hitch.
For a trailer hitch use the Curt Trailer Hitch # C13052 because it has the most bumper clearance for use with a bike rack. This is a Class III, 2 inch hitch which is a bolt-on installation so no drilling will be required to install it on your Land Rover; the hitch is made in the USA and comes with a lifetime warranty. I have added a photo for you to take a... view full answer...
Go To Results